ALKAN® · Street & Road Lighting

Venüs Small

140–200 W · 20,300–30,000 lm · IP66

Request a quote Request a DIALux calculation

Why this luminaire

Even light on the carriageway, little load on the pole

A street meets its lighting class only when the light lands evenly, and a pole carries only so much. Venüs Small is built around both limits: an asymmetric optic directs the light onto the carriageway, and a low-profile body with a wind area (EPA) of 0.15 m² keeps the sail load small. Output runs from 20,300 to 30,000 lm at 140–155 lm/W, so one luminaire covers urban streets, collector roads and open car parks. Every project is calculated to EN 13201 in DIALux evo.

Built for the job

Die-cast aluminium body

The housing is the heat sink: cooling fins integrated into the cover draw heat away from the LEDs, protecting light output and lifetime.

4 mm clear tempered glass

The tempered glass seals the optic from weather and wipes clean, so the street stays close to its designed light level.

IP66

Rated IP66 (EN 60529): dust-tight and protected against powerful water jets.

IK09 · IK08

Impact resistance to EN 62262: IK09 on the body, IK08 on the glass.

−40 °C to +50 °C

Rated for ambient temperatures from −40 °C to +50 °C, from mountain passes to coastal roads in summer.

184–264 VAC

A wide supply window: 184–264 VAC at 50/60 Hz.

60,000 hours

LED lifetime of 60,000 hours keeps visits to the pole to a minimum.

Colour rendering Ra>70

Ra>70 in 3000 K, 4000 K or 6500 K: warm white for residential streets, neutral white for main roads.

Where it fits

Streets and roads

Urban streets, collector roads and through roads.

Residential areas

Residential streets, paths and cycle routes.

Car parks and squares

Open car parks, squares and public spaces.

Road lighting classes

M classes

Per EN 13201: motorised traffic on roads with medium to high driving speeds; based on road surface luminance.

C classes

For conflict areas such as junctions, roundabouts and shopping streets; based on illuminance.

P classes

For pedestrians and cyclists on footways, cycle paths and low-speed residential streets; based on illuminance.

Engineering notes

Mounting

Tilt adjusts in 0°, 5°, 10° and 15° steps on a Ø42–60 mm spigot. Pole height, spacing and tilt come from the EN 13201 calculation.

Choosing the optic

The asymmetric optic comes in mid-power and high-power LED versions. We compare them in DIALux evo against your geometry and pick the one that reaches the target with the fewest luminaires.

Controls

No dimming interface is specified for this luminaire. If your project needs one, we check the options with the manufacturer before we quote.

Maintenance

A latched cover and blade terminals give safe access for maintenance. Clean the glass periodically to hold the designed light levels; the calculation already includes a maintenance factor.

Certification and standards

CE: the manufacturer’s EC declaration of conformity under Low Voltage Directive 2014/35/EU (January 2025) names the AKYAL series.

CE 2025 (PDF)

ENEC: licence HN 69291507 from TÜV Rheinland InterCert for 53.AKYAL xxxV-⁠y, 140–⁠200 W.

ENEC HN 69291507 (PDF)

CB test certificate DE 2-⁠043965 (TÜV Rheinland LGA, 2025-02-20) for 53.AKYAL xxxV-⁠y (IEC 60598-⁠2-⁠3).

CB DE 2-043965 (PDF)

Coverage is stated as published by ALKAN®. Certificate copies come with every offer.

Standards: EN 60598-1, EN 60598-2-3.

Datasheets for every variant are in the variants table on this page; LDT/IES photometric files are available on request.

Questions we hear

Can it replace my existing luminaires?

In most retrofit projects, yes. We check the existing mounting points and the target values in a calculation before we quote, so you know the result in advance.

What tolerances apply to these values?

Tolerances: power +2.5%, luminous flux −10%, efficacy −5%. Our calculations take this into account.

Bring us the road, we will bring the layout

Send us drawings, photos or a few measurements of the site. You get a DIALux layout, the quantities and an offer from the official ALKAN® distributor.

Request a DIALux calculation

Technical specifications

Power	140–200 W
Luminous flux	20,300–30,000 lm
Efficacy	140–155 lm/W
Colour temperature	3000 K / 4000 K / 6500 K
Colour rendering	Ra>70
Optics	asymmetric
Ingress protection	IP66
Impact resistance	Body IK09, glass IK08
Ambient temperature	−40 °C to +50 °C
Supply	184–264 VAC 50/60 Hz
Driver	ENEC-certified, protected against voltage surges
LED lifetime	60,000 h
Housing	Injection-moulded aluminium
Cover / optic	4 mm clear tempered glass
Finish	electrostatic powder coating, textured grey
Wind area (EPA)	0.15 m²
Mounting	0°, 5°, 10°, 15° tilt adjustment
Spigot	Ø42–60 mm
Standards	EN 60598-1, EN 60598-2-3
Certificates	CE declarationENEC luminaire licenceCB test certificate

Product code	Version	Power	Luminous flux	Efficacy	W × L × H	Weight	Datasheet (PDF)
53.AKYAL 140V-M	Mid-power LED	140 W	20,300 lm	145 lm/W	298 × 500 × 103 mm	6.30 kg	PDF
53.AKYAL 150V-M	Mid-power LED	150 W	21,450 lm	143 lm/W	298 × 500 × 103 mm	6.30 kg	PDF
53.AKYAL 160V-M	Mid-power LED	160 W	22,400 lm	140 lm/W	298 × 500 × 103 mm	6.30 kg	PDF
53.AKYAL 180V-M	Mid-power LED	180 W	26,100 lm	145 lm/W	298 × 500 × 103 mm	6.50 kg	PDF
53.AKYAL 200V-M	Mid-power LED	200 W	28,200 lm	141 lm/W	298 × 500 × 103 mm	6.50 kg	PDF
53.AKYAL 140V-H*	High-power LED	140 W	21,700 lm	155 lm/W
53.AKYAL 160V-H*	High-power LED	160 W	24,480 lm	153 lm/W
53.AKYAL 180V-H*	High-power LED	180 W	27,900 lm	155 lm/W
53.AKYAL 200V-H*	High-power LED	200 W	30,000 lm	150 lm/W

* No separate PDF datasheet is issued for this code.

Tolerances: power +2.5%, luminous flux −10%, efficacy −5%.

Road and street luminaire with a latched cover and blade terminals for safe maintenance access, and a low-profile shape that reduces wind load. Cooling fins are integrated into the cover, and a seamless silicone gasket seals the housing against dust and moisture at any tilt angle.